设为首页 | 添加收藏 | 我的商务办公室 | 繁體中文 | English
欧洲标准DD CEN/TS 15534-3:207Wood-plastics composites (WPC) —Part 3: Characterisation of WPC products
来源: 作者: 发布日期:2014-08-07 阅读次数:1093 评论数:0 收藏 打印 
DD CEN/TS 15534-3:207Wood-plastics composites (WPC) —Part 3: Characterisation of WPC products

1 Scope

This Technical Specification identifies the required and optional properties of wood-plastics composite (WPC)products. It is intended to be used as a basis for the specifications of WPC products. This part is applicable to WPC products intended to be used as decking and siding.NOTE Other applications may be covered when this document will be revised.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

EN 310, Wood based panels — Determination of modulus of elasticity in bending and of bending strength

EN 317, Particleboards and fibreboards — Determination of swelling in thickness after immersion in water

EN 318, Wood-based panels — Determination of dimensional changes associated with changes in relative humidity

EN 321, Wood based panels — Determination of moisture resistance under cyclic test conditions

EN 477, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors —Determination of the resistance to impact of main profiles by falling mass

EN 479, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors —Determination of heat reversion

EN 789:2004, Timber structures — Test methods — Determination of mechanical properties of wood based panels

EN 927-6, Paints and varnishes — Coating materials and coating systems for exterior wood — Part 6:Exposure of wood coatings to artificial weathering using fluorescent UV lamps and water

ENV 1156, Wood-based panels — Determination of duration of load and creep factors

EN 1383, Timber structures — Test methods — Pull through resistance of timber fasteners

EN 13446, Wood-based panels — Determination of withdrawal capacity of fasteners

EN 13823, Reaction to fire tests for building products — Building products excluding floorings exposed to the thermal attack by a single burning item

EN 13893, Resilient, laminate and textile floor coverings — Measurement of dynamic coefficient of friction on dry floor surfaces

CEN/TS 15534-1:2007, Wood-plastics composites (WPC) — Part 1: Test methods for characterisation of WPC materials and products

CEN/TS 15534-2, Wood-plastics composites (WPC) — Part 2: Characterisation of WPC materials

CEN/TS 15534-3:2007

EN ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test(ISO 179-1:2000)

EN ISO 877, Plastics — Methods for exposure to direct weathering, to weathering using glass-filtered daylight,and to intensified weathering by daylight using Fresnel mirrors (ISO 877:1994)

EN ISO 2813, Paints and varnishes -- Determination of specular gloss of non-metallic paint films at 20 degrees, 60 degrees and 85 degrees (ISO 2813:1994, including Technical Corrigendum 1:1997)

EN ISO 4628-6, Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 6: Assessment of degree of chalking by tape method (ISO 4628-6:2006)

EN ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps(ISO 4892-2:2006)

EN ISO 6603-2, Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2:Instrumented puncture test (ISO 6603-2:2000)

EN ISO 9142:2003, Adhesives — Guide to the selection of standard laboratory ageing conditions for testing bonded joints (ISO 9142:2003)

EN ISO 9239-1, Reaction to fire tests for floorings — Part 1: Determination of the burning behaviour using a radiant heat source (ISO 9239-1:2002)

EN ISO 11925-2, Reaction to fire tests — Ignitability of building products subjected to direct impingement of flame — Part 2: Single-flame source test (ISO 11925-2:2002)

ISO 7724-1, Paints and varnishes — Colorimetry — Part 1: Principles

ISO 7724-2, Paints and varnishes — Colorimetry — Part 2: Colour measurement

ISO 7724-3, Paints and varnishes — Colorimetry — Part 3: Calculation of colour differences

责任编辑:王艳艳

发表评论

共0条 [查看全部]
 
好评
 
0% 0
中评
 
0% 0
差评
 
0% 0
 
好评 中评 差评